Brunswick Stump Removal & Tight Access
Stump grinding 300–400 mm below ground in Brunswick, including tight-access side paths and courtyards. No regrowth, clean finish.
- Free quotes
- Fully qualified & insured
- 16+ years

Stump removal and tight access in Brunswick, done properly
Stump grinding in Brunswick (3056) is an easy job for us to slot in. Api quotes it free, and for most stumps the crew is in and out in an hour or two with the yard swept behind them.
The nearest suburbs we also cover are Princes Hill (2 km), Parkville (2 km), Travancore (3 km), so a job in Brunswick is often paired with one next door.
We measure the stump, check for stones, pipes and cables — Dial Before You Dig where there is any doubt — and set up the grinder. The cutting wheel takes the stump down in passes to 300–400 mm below ground level, then follows the main lateral roots out. The grindings go back into the hole, mounded slightly because they settle, and the surrounding lawn or paving is left clean.
If you plan to build, pave or plant a tree in the same spot, tell Api when he quotes: we can grind deeper, remove the grindings and backfill with soil instead, or take the main roots further out so the ground is ready for what comes next.
Stump Removal & Tight Access in Brunswick — what we do
Stump grinding
Down to 300–400 mm below ground, surface roots chased out.
Tight-access grinding
Compact and mini machines for side paths and courtyards.
Large & multi-stem stumps
Mature hardwoods, palms and cypress rows.
Backfill & tidy finish
Grindings back in or removed and replaced with soil.
A tip from Api
If the stump is near a boundary, fence or retaining wall, we grind it from the accessible side with the guard on and the neighbour’s side protected. Tell Api if the tree was a shared one — it affects who owns the job.
The full service pages: Stump Removal and Tree & Palm Removal — every one available in Brunswick.
Guides from Api: Local tree removal companies in Melbourne: what a good one actually does · Tree removal contractors: the checks to make before you sign in Melbourne
Do you need a permit to remove a tree in Brunswick?
Before anything is cut in Brunswick, the permit question comes first, and the answer depends on Merri-bek City Council.
In Merri-bek a Tree Works Permit is required to remove a mature tree, or to prune more than 15 per cent of its canopy, on private property. A mature tree is 8 m or taller with a single trunk diameter greater than 40 cm, or multiple trunks adding to more than 40 cm, measured 1.2 m above the ground; trees on the Significant Tree Register are covered regardless of size.
Pruning under 15 per cent needs no permit, but the council recommends an AQF Level 3 arborist and before-and-after photos. Where a tree is protected by an overlay or by a condition on an earlier planning permit, a planning permit (or an amendment) is the route instead, and the planning scheme takes precedence over the local law.
The rule sits in clause 2.5 of the General Local Law; the Urban Forest team on 9240 1111 handles questions.
Source: Merri-bek City Council — trees on private property, 9240 1111. Read 13 September 2026; councils change their local laws, so Api checks the current rule when he quotes.
Across Victoria since 15 September 2025
Clause 52.37 Canopy Trees
A canopy tree is a tree more than 5 m tall, with a trunk circumference over 0.5 m at 1.4 m above the ground and a canopy at least 4 m across. In a residential zone a planning permit is needed to remove, destroy or lop one in a residential zone if the lot is vacant, or, where there is an existing house, if any part of the trunk is within 6 m of the narrowest street frontage or 4.5 m of the rear boundary.
Dead trees, emergency and safety works, maintenance pruning and listed weed species are exempt; councils usually condition a permit on planting a replacement canopy tree, and most decide these through VicSmart in about ten business days.
What this means for you: tell Api where the tree sits on the block and he will tell you whether a permit is needed before anything is cut — and where one is, we can prepare the arborist assessment the application needs.
Stump removal jobs by Api and the crew
Real jobs, real photos — Api, the crew and the truck, across Melbourne’s inner north. Nothing staged, nothing stock.
Stump removal around Brunswick
The same crew, the same day rates, in the suburbs next door:
Other services in Brunswick
Tree services made easy
At Aps Tree Removal, we simplify the tree and hedge removal experience with a clear, step-by-step approach.
Contact us
Want to learn more? Call 0422 856 090 or send the form and speak with Api.
Get a quote
Getting a quote is quick, easy, and free.
On-site inspection
A quick, thorough site assessment — species, access and risks.
Professional removal
Clean and safe work, chipped and cleaned up — no mess, no hassle.
What clients across Melbourne’s inner north say
Brunswick Stump Removal & Tight Access — common questions
Do I need a permit to remove a tree in Brunswick?
Yes, for a “mature tree” — 8 m or taller with a trunk diameter over 40 cm at 1.2 m (single or combined) — or a tree on the Significant Tree Register: Merri-bek requires a Tree Works Permit to remove it or to prune more than 15 per cent of its canopy. Trees protected by an overlay or a planning-permit condition need a planning permit instead. Across Victoria, Clause 52.37 Canopy Trees also applies since 15 September 2025: a planning permit is needed to remove, destroy or lop one in a residential zone if the lot is vacant, or, where there is an existing house, if any part of the trunk is within 6 m of the narrowest street frontage or 4.5 m of the rear boundary. Api checks both at the quote.
How much does stump removal cost in Brunswick?
Priced per stump, by size and access, no charge for the quote. Removing the grindings and backfilling with soil is a small extra if you want turf straight over the top.
How long does it take?
An hour for a small stump, half a day for a large hardwood. We give you a time window and keep to it.
Can you get in if the access is tight?
Yes — it is most of what we do. The compact grinder needs about 750 mm; beyond that we have a mini machine and hand tools for the truly awkward spots.
What happens to the waste?
The grindings go back in the hole unless you ask for them to be taken away and replaced with soil. Anything above that is loaded on the truck and the area is raked and blown clean.
How deep do you grind, and can I plant or pave over the spot?
Deep enough that nothing regrows and nothing gets in the way of what you do next — 300–400 mm as a rule. Tell Api what you plan to put there and he will grind to suit.



